Splunk uba documentation12/1/2023 The search windows in Splunk UBA's micro-batch queries are expanded to ingest more events to compensate for lags during data ingestion. For example, if the delay property is set to 10800 seconds (3 hours), then the backtrace property should be set to at least 3 hours. Do not set the backtrace property to a period of time lower than that of the datasource delay property.This is described in the text immediately below the table. If a data source is restarted inside the window of time configured by .time.in.hour, Splunk UBA will continue to ingest events where it left off before the data source was stopped and attempt to catch up so there is no more lag.The events between 12:00AM and 2:00AM cannot be recovered. For example, if a data source was stopped at 12:00AM and not restarted again until 6:00AM, and the .time.in.hour is 4 hours, Splunk UBA will ingest events that occurred at 2:00AM. If a data source is stopped for a longer period of time than the configured .time.in.hour interval, some events will be lost.The window of time that determines when to begin data ingestion after a data source is stopped and then restarted. See Configure Kafka data ingestion in the Splunk UBA Kafka Ingestion App manual.Ĭ.time.in.hour Setting this property for an individual data source overrides the setting of the .conds property and also the .conds property for Kafka ingestion. For example, to configure an interval of 120 seconds for a data source named exampledatasource, use the following property and value setting: You can configure the query interval for any individual data source by adding the data source name to the end of the property. If you specify 120 seconds as the interval, then a query is run every 120 seconds for 120 seconds worth of events.ĭo not configure the interval to exceed 240 seconds (4 minutes).The default is 60 seconds, meaning that a query is run every 60 seconds for 60 seconds worth of events, starting from the time defined by .conds.The length of the time in seconds for each batch query. See Configure Kafka data ingestion in the Splunk UBA Kafka Ingestion App manual. For example, to configure delay of 120 seconds for a data source named exampledatasource, use the following property and value setting: You can configure the data ingestion start time for any individual data source by adding the data source name to the end of the property. The query runs on the events within the specified interval of time defined by .conds.ĭo not configure this property to exceed 10800 seconds (3 hours). Specifying a delay of 120 seconds means that the first batch query begins processing events at 1:00 PM. For example, if data ingestion is enabled at 10 seconds past 1:02 PM, then the beginning of the minute is 1:02 PM. The default is 180 seconds (3 minutes) earlier than the start of the current minute. The point in time when Splunk UBA begins data ingestion. Run the following command to synchronize the cluster in distributed deployments:.In the /etc/caspida/local/conf/uba-site.properties file, add or edit the properties in the table.To configure the properties of the queries: Monitor your Splunk UBA instance directly from Splunk Enterprise with the Splunk UBA Monitoring app.See the error messages and descriptions in Data Sources (DS).See the Splunk Data Source Lag indicator in View modules health.To monitor the status of your data ingestion: Using time-based search enables Splunk UBA to provide monitoring services for the status of your data ingestion. This is the default method for getting data into Splunk UBA. Splunk UBA performs micro-batched queries in 1-minute intervals against the Splunk platform to pull in events. The Splunk platform pushes data to Splunk UBA using Kafka ingestion.Splunk UBA performs real-time indexed queries against the Splunk platform to pull data in to Splunk UBA.Splunk UBA performs time-based searches against the Splunk platform to pull data in to Splunk UBA.How data gets from the Splunk platform to Splunk UBAĭata is ingested into Splunk UBA from the Splunk platform in the following ways:
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |